Motherboard replacement

-
By now, I've replaced three computers' motherboards, two of them were brand new and the third was actually relocated from one box to another. I have used a couple of cheap Pentium D 2.66Ghz to equip the new ones (around 115 Euros each taxes included). The motherboards came with this nice install video. So if you wonder what's all this thing about LGA775 socket you may have a look at it. In case you wonder LGA stands for Land Grid Array and it is type pin-less chip carrier, similar to BGA but where the balls have been replaced by flat conductive pads. So now the pins are on the socket instead of on the chip and you have to exercise caution not to damage them (or you'll need a new motherboard).

As usual the replacement of the motherboard of a computer (and sometimes also the graphics card) is not without problems: All my systems had some version of an AMD K7 processor, so the change meant a new CPU type, new chipset and in one case, new graphics card (as the Asrock775Twins-HDTV comes with its own ATI X200 embedded graphics card). In two systems MS Windows XP refused to work at all, so a "Repair install" was required where new chipset drivers were installed. Ubuntu Linux worked in both cases, but without taking advantage of the new dual core processor. SuSE Linux however did not work with the 775Twins card till "noapic" command was added at system boot. At any rate, all the systems required me to install the new graphic drivers whenever graphic card was changed. It was not that bad but it kept me busy.

Now I have added SMP support by adding linux-image-2.6.15-25-686 that can actually handle Pentium Pro/Celeron/Pentium II/Pentium III/Pentium IV with SMP support. It just worked and now I have the two cores working. The system feels much more responsive when playing a video and opening a spreadsheet at the same time (not that I think this is specially useful but you get the idea).

Comments

Post a Comment

Popular posts from this blog

VFD control with Arduino using RS485 link

-
Image
Variable Frequency Drives ( VFD ) allow the control of spindles so speed can accurately be controlled and a detailed acceleration profile for the spindle and reverse rotation can all be handled. In essence a VFD is an three phase inverter for three-phase AC motor. I am using a popular (I mean cheap) Chinese VFD and though the reference manual is not great, I could see there is a built-in RS-485 port. I usually control the start, stop and speed selection using the keyboard on the unit but I thought it will be more useful if I could control everything from the same Arduino is doing our CNC table control. Some cheap RS-485 off eBay and some lines of code later, I can start, stop and change the speed from an Arduino. What a cool thing to have! Some configuration of your VFD are needed before you can use it like that.  You need to set PD163=1 (I am using address 1 in the code). PD=164=1 (for setting serial to 9600bps) and PD165=0 (for using ASCII and 8N1 character format)
Read more

How to get sinusoidal s-curve for a stepper motor

-
Image
After some experimentation, and delving a bit into the math of motion, I realized there can be a significant difference on the motion of a machine by just making small changes. A common and popular approach to smooth one axis of motion is to use a trapezoidal speed pattern, where acceleration and deceleration are uniformly accelerated movements (aka constant acceleration motion) separated by a portion happening at cruising speed. The problem comes with the fact that, while that approach is simple to understand and to code, it does contain sudden changes in the acceleration, that show as spikes on the acceleration derivative, called jerk. These sudden changes in the acceleration translate into undesired vibration in our machines. Most of that can be eliminated by selecting a motion pattern that does not contain sudden changes of acceleration. If we chose a mathematical function for our speed whose second derivative is continuous, then we reduce system vibration quite a lot. One ma
Read more

Stepper motor step signal timing calculation

-
Image
While we use stepper motors in many devices, the timing of the step signals is not always well understood. Most of us can see how a fixed speed is a bad idea unless the speed of motion is really slow, but it is fixed speed what is really to generate with simple code. You just can use the Arduino Blink example to send a fixed frequency of pulses to a stepper motor driver. If too slow, just reduce the delay value. But for most real-life applications variable speed controls will perform better. These systems will speed up the motor to a given maximum speed and it will slow it down to stop at the desired step count. But understanding the math behind this process is sometimes not obvious. Let us start with the simple case of the so-called trapezoidal speed motion profile. Here motion takes place in three phases: acceleration, constant speed (cruising) and deceleration. But the point is how can our code create such a behavior. Stepper motor drivers usually accept two signals to control
Read more